| |
|
|
|
|
| Chemical and
Physical Properties |
Solubility
in water: Insoluble
Flash Point: >95¡ãC (200¡ãF)
Specific Gravity: 1.06-1.1(modified)+-
Appearance: Clear
Curing Speed with UV: <18 second depending on the intensity of
UV
Odor: Mild
Shelf Life: 18mths @ 20¡ãC
Viscosity MM101: 100-300 Cps (nominal) MM103: 1500-2500 Cps (nominal)
Refractive Index 1.49 ASTM D-1218 |
| Cured Performance
|
Tensile
Shear Strength: 22-28 N/mm(2)
Tensile Strength: 20-26 N/mm(2)
Tensile Compression Shear:
Glass-to-Glass 2300 psi (glass shatters) DDCM D-250
Glass-to-Steel 1700 psi (glass shatters) DDCM D-251
Typical Gap Design: 0.05-0.08mm(MM101-MM103)
Maximum Gap Design: 0.08-0.1mm (MM101-MM103)
Gap Size / Strength Relationship Minimum Gap >50% strength
Medium Gap >70% strength
Maximum Gap >100% achievements
Tensile at Break 7,000 psi ASTM D-638
Modulus of Elasticity 38,000 psi ASTM D-638
Elongation at Break 125% ASTM D-638
Durometer Hardness D70 ASTM D-2240
Thermal Limit (brittle/degrades) -50¡ãC to 180¡ãC
DCCM refers to DDC Standard Test Method. |
| Cure Data
|
UV Light - Using 365 nm wavelength UV light.
| |
Curing Time (seconds)
|
Intensity (mW/cm2)
|
|
Fixture between glass slides
|
40, 35, 30, 25 (app.)
|
7, 20, 50, 100
|
| Nominal cure depth (0.25 inch) |
53, 48, 46, 42 (app.)
|
7, 20, 50, 100
|
|
| Factors Affecting
Curing |
Applying the unqualified UV lamp with
different wavelength. (suitable wavelength: 365nm, refer to our graph)
Applying the very low intensity UV light. ( Below 10 mW/cm2 )
Full range lamps provide faster cures than filtered sources.
All UV sources degrade with use a certain long period. Check output
with a radiometer.
Thicker UV glue films require longer curing time.
Light intensity decreases
when the distance from UV source increases. |
| Reactivity
Data |
|
Stability:
Stable
Hazardous Polymerization: Will not occur
Hazard Decomposition Products (non-thermal): None
Incompatibility: None
|
| Shipping Regulations |
|
Dot
(49 CFR 172)
Proper Shipping Name Unrestricted
Hazard Class or Division Unrestricted
Identification Number None
IATA
Proper Shipping Name Unrestricted
Class or Division Unrestricted
UN or ID Number None
IMO
Substance NA
Marine Pollutant Status NA
Class NA
Subsidiary Risk Label NA
IMDG Code Page NA
UN Number NA
|
| Instructions
|
For
Use Ensure parts are clean, dry and free from oil and grease.
Procedure For Application
Product is normally hand applied from the bottle.
Storage
Store in a cool area (ideal temp. below 18¡æ) and out of direct sunlight.
Refrigerated storage extends shelf life.
Presentation
Bottles: --------------------250ml
Health and Safety In Use
Irritant. In case of contact with the skin, please wash with
plenty of soap and water immediately. Never using other solvents
to remove adhesive for skin or eyes. |
| |
|
The
above information contained herein is produced in good faith and
is believed to be reliable but is for guidance only. DDC and its
agent cannot assume liability or responsibility for results obtained
in the use of its products by person whose methods are outside or
beyond our control. It is the users responsibility to determine
the suitability of any of the products and methods of use or preparation
prior to use mentioned in our literature and furthermore the users
responsibility to observe and adopt such precautions as may be advisable
for the protection of personnel and property in the handling and
use of any of our products.
|
| |
| |
|
|
